leaking amal 2 jet
Moderators: John@sos, charlesp, Charles uk, RickUK, Petergalileo
leaking amal 2 jet
the amal 2 jet on my motor leaks from the banjo bolt & also where the fuel hose connects to the float chamber.have replaced washers on the banjo but still no luck.
is there a way to stop the leaks ?
cheers
jason
is there a way to stop the leaks ?
cheers
jason
Re: leaking amal 2 jet
It could be a leak from somewhere else that's collecting at the lowest point.
What type of fuel pipe is it, has it gone hard, also what's the thread like on the base of the amal.
What type of fuel pipe is it, has it gone hard, also what's the thread like on the base of the amal.
Re: leaking amal 2 jet
Any tiny cracks on the fittings?
Re: leaking amal 2 jet
It could also be a sticking float causing the float bowl to over fill and leak out of the tell tale (Same as when you operate the tickler) The fuel would then dribble down the side of the float bowl and look just like it is leaking from the banjo washers and/or the fuel tube connection.
My SD sometimes does the opposite to that and the float sticks in the up position and the engine starves of fuel!
My SD sometimes does the opposite to that and the float sticks in the up position and the engine starves of fuel!

Re: leaking amal 2 jet
thanks for the replies.
it has a rubber hose that seems quite hard but no cracks or anything,o leak from the fuel tap,thread on the base of the carby seems fine.
i don`t think it`s a sticking float,as i have to operate the tickler a fair bit on start up to get fuel flowing.
cheers
jason
it has a rubber hose that seems quite hard but no cracks or anything,o leak from the fuel tap,thread on the base of the carby seems fine.
i don`t think it`s a sticking float,as i have to operate the tickler a fair bit on start up to get fuel flowing.
cheers
jason
- Collector Inspector
- Posts: 4196
- Joined: Sun Jun 29, 2008 4:32 am
- Location: Perth Western Australia
- Contact:
Re: leaking amal 2 jet
Jason
Pull it apart and inspect each bit for correct operation then put it all back together with new washers etc.
Get a new fuel line if it is hard and "Rubber".
Old rubber on the outside = old rubber on the inside,
Old rubber gets into everything including threads and sealing washers?
B
New font colour for 2014
Pull it apart and inspect each bit for correct operation then put it all back together with new washers etc.
Get a new fuel line if it is hard and "Rubber".
Old rubber on the outside = old rubber on the inside,
Old rubber gets into everything including threads and sealing washers?
B
New font colour for 2014
A chicken is one egg's way of becoming others
Re: leaking amal 2 jet
i`ve had the carby apart previously & cleaned everything,there was a fair bit of rubbish in it,new washers etc but still leaks.so should i pull it apart again ?
where would i get a new fuel line from ?
thanks again for the replies
jason
where would i get a new fuel line from ?
thanks again for the replies
jason
- Stelios_Rjk
- Posts: 1458
- Joined: Sun Jun 17, 2012 10:15 pm
- Location: Athens - Greece
Re: leaking amal 2 jet
Detailed pictures of the carb disassembled may help.
Also a bent needle, a float with fuel inside or a float attached in the wrong position on the needle maybe one of your problems.
Also are the surfaces flat where the washers sit?
Also a bent needle, a float with fuel inside or a float attached in the wrong position on the needle maybe one of your problems.
Also are the surfaces flat where the washers sit?
I love the 10600/145 turns!!!
Re: leaking amal 2 jet
thanks stelios,i`ll pull the carby apart again soon & post up some pics
Re: leaking amal 2 jet
maybe check your fuel tap as well, I once had one that was leaking and the fuel was running down the line to the carb
Re: leaking amal 2 jet
hi chris,no not the fuel tap mate.i`ve had this problem since i got the motor,put a new fuel tap in & it`s still doing it