New to the board and I have a BMB Swordfish

Talk about interesting old outboards which aren't Seagulls here

Moderators: John@sos, charlesp, Charles uk, RickUK, Petergalileo

Post Reply
FenTiger
Posts: 4
Joined: Wed Aug 29, 2018 4:37 pm
Location: Lancashire

New to the board and I have a BMB Swordfish

Post by FenTiger »

Good morning all.
I found this forum while searching for information about the Britannia Swordfish.

The motor was passed to me a couple of years ago by a friend who had cleared the shed of a deceased gentleman acquaintance.
I have been bringing old motorcycles and bicycles back to life previously, so restoring an outboard motor is all new to me.
There's the excuses declared for when I inevitably ask dumb questions.

I've no idea what to do with this engine when restored as I don't possess a vessel to clamp it to :lol:

The motor is complete apart from the original tiller arm missing.
I believe it to be a MK 1, based on the carburettor top (referenced from the user manual)
The carburettor leaked badly. Subsequent investigation revealed a stripped thread in the bottom of the carb body. 5/8 UNEF apparently (0.625 x 24tpi)
I have a lathe, so I intend to insert a newly threaded sleeve into the carb body. I sourced a 5/8 UNEF tap from Ebay.
The fuel tank is badly dented and probably leaks.
I had the engine running briefly before consigning it to the projects awaiting shelf.

Any comments would be welcomed. Any guess as to age? Any suggestions for restoring the tank?

Photos attached, hopefully
Attachments
Attachment-5.jpeg
Attachment-4.jpeg
Attachment-3.jpeg
Attachment-2.jpeg
Attachment-1.jpeg
User avatar
Oyster 49
Posts: 3311
Joined: Tue Oct 26, 2010 6:55 pm
Location: Derbyshire, UK

Re: New to the board and I have a BMB Swordfish

Post by Oyster 49 »

Welcome to the forum 8)

Yes you have the later iteration of the BMB called the swordfish, produced from around 1949 approx.
User avatar
cookie1
Posts: 234
Joined: Wed Apr 13, 2016 10:04 pm
Location: Orkney , Scotland

Re: New to the board and I have a BMB Swordfish

Post by cookie1 »

Nice motor ! I have a few motors here with bashed tanks , I've often wondered if you could get them back in reasonable shape by sealing the filler cap and applying pressure with compressed air via the tap fitting . Has anyone tried it ?

cheers
FenTiger
Posts: 4
Joined: Wed Aug 29, 2018 4:37 pm
Location: Lancashire

Re: New to the board and I have a BMB Swordfish

Post by FenTiger »

Thanks for the info.
I’m dubious as to whether the compressed air idea would work satisfactorily. Surely if the pressure is high enough to deform the material, the deformation would be general rather than selective with the dents.
User avatar
Nudge
Posts: 827
Joined: Sun Feb 15, 2015 2:43 am
Location: Auckland, New Zealand

Re: New to the board and I have a BMB Swordfish

Post by Nudge »

It is done with a water blaster.... Look it up on youtube!
"THE KING OF BLING"!
Is it better to over think, than not think at all?
Ferrier120
Posts: 31
Joined: Tue Oct 21, 2014 1:38 pm
Location: Devon

Re: New to the board and I have a BMB Swordfish

Post by Ferrier120 »

This looks more like the Britannia rather than the Swordfish.
Attachments
Britannia and Swordfish.jpg
FenTiger
Posts: 4
Joined: Wed Aug 29, 2018 4:37 pm
Location: Lancashire

Re: New to the board and I have a BMB Swordfish

Post by FenTiger »

Thank you for that :P
It is indeed a Britannia, and not a Britannia Swordfish.

The carb repair is progressing. I've bored out the carb body to accept a threaded sleeve. The sleeve is 50% done, and will be finished when I procure a tap wrench big enough to hold the 5/8" tap.

I need to replace the throttle cable. I could have achieved this myself from my bicycle stuff, but the cable has a nipple on both ends.
Could anyone recommend a source for a ready made item?
User avatar
Nudge
Posts: 827
Joined: Sun Feb 15, 2015 2:43 am
Location: Auckland, New Zealand

Re: New to the board and I have a BMB Swordfish

Post by Nudge »

Just soft solder a bit of copper on the end. if it is smaller than that drill a hole in some aluminium to make a mould. Heat up the aluminium hot enough to melt the solder and dip the in of the cable into it..... wait for it to cool down.
"THE KING OF BLING"!
Is it better to over think, than not think at all?
FenTiger
Posts: 4
Joined: Wed Aug 29, 2018 4:37 pm
Location: Lancashire

Re: New to the board and I have a BMB Swordfish

Post by FenTiger »

Nudge wrote:Just soft solder a bit of copper on the end. if it is smaller than that drill a hole in some aluminium to make a mould. Heat up the aluminium hot enough to melt the solder and dip the in of the cable into it..... wait for it to cool down.
Thank you for the info. Just shows that I need to get my brain into the “make it myself mode”.
Nothing to lose apart from a foot of cable :lol:
User avatar
Hugz
Posts: 3282
Joined: Wed Mar 14, 2007 4:41 am
Location: Sydney

Re: New to the board and I have a BMB Swordfish

Post by Hugz »

Best to tin the cable first ie dip in flux, heat and let solder impregnate through the cable and then wipe with a wet cloth. It will bond better when dipping as Nudge mentioned.
Post Reply