Vessel befitting a Seagull at last.
Moderators: John@sos, charlesp, Charles uk, RickUK, Petergalileo
Re: Vessel befitting a Seagull at last.
Ha! 15inch mags, I think HR are 14". Been concentrating on my 60's transit van as of recent.
Is this near you: http://www.gumtree.com.au/s-ad/ipswich/ ... 1099815220
Is this near you: http://www.gumtree.com.au/s-ad/ipswich/ ... 1099815220
Re: Vessel befitting a Seagull at last.
Rats; yes 14's on the mighty HR.
Oh well im shore we will see the boat on the water with your EDL at some stage.
The van is within driving range if you need it to be, but i'm not home till the 10th, so couldn't see it before then. Sorry.
Oh well im shore we will see the boat on the water with your EDL at some stage.
The van is within driving range if you need it to be, but i'm not home till the 10th, so couldn't see it before then. Sorry.
TC - 1960 LLS - 1961 LLS - 1966 THCL - 1968 EFNRL - 1986
Re: Vessel befitting a Seagull at last.
Holden HR were 13" the HT was 14" both had the same PCD.
Hugz are you bringing it to the Nationals looks too nice to leave parked for another 5 years.
John
Hugz are you bringing it to the Nationals looks too nice to leave parked for another 5 years.
John
- Charles uk
- Posts: 4960
- Joined: Wed Feb 27, 2008 4:38 pm
- Location: Maidenhead Berks UK
Re: Vessel befitting a Seagull at last.
Hugo if that boat ever goes missing from your storage location don't bother looking for it, it will be inside a 20 foot container on top of a Bolwell Nagari on it's way to my house, don't worry I will treasure.
It's good to know your still around.
It's good to know your still around.
Make it idiot proof and someone will make a better idiot.
Re: Vessel befitting a Seagull at last.
It's got 'oles in it!
I have all the materials ready to go but not the place to work. I was hoping to find a retired chippy etc who wanted to make a few $'s but alas not to be found.... yet.
I should bring it down to SA. They are all suits around here
I have all the materials ready to go but not the place to work. I was hoping to find a retired chippy etc who wanted to make a few $'s but alas not to be found.... yet.
I should bring it down to SA. They are all suits around here
Re: Vessel befitting a Seagull at last.
I've forgotten about the Bolwell Nagari. Geez, they have gone up in price.... I remember when they were about $4K.
http://bolwellcarclubnsw.com/page36.htm
http://bolwellcarclubnsw.com/page36.htm
- Charles uk
- Posts: 4960
- Joined: Wed Feb 27, 2008 4:38 pm
- Location: Maidenhead Berks UK
Re: Vessel befitting a Seagull at last.
I couldn't afford one then, I looked at a coupe in Vic but it had a P76 in the front & a Huntsman inside, poms don't feel comfortable with wildlife that big!
Make it idiot proof and someone will make a better idiot.
Re: Vessel befitting a Seagull at last.
It looks in quite sound condition I can see the keel slot needs plugging how about a few photos of the damaged areas.
John
John
Re: Vessel befitting a Seagull at last.
Will do as soon as it stops raining rats and roos. Pissing down here!
Re: Vessel befitting a Seagull at last.
Needs a good dry out. Not the best photos:
Plank next to keel. Inside looking down.
Another rotted plank on bottom.
Starboard side. Think at some stage it must have been sitting on its side outside.
The quarters and some hanging knees are rotted too though I can do those. It is mainly to scarf in about five plank repairs.. Need to put some floorboards in as well. Planks made of 1/4"marine ply. I have 6mm sheet.
A shipwright also advised me to add a heavier timber skeg keel to the existing. It is the same as this all along. Also suggested a bulkhead about 2ft back to strengthen the bow quarters.
Ideally it would be good to replace all planks. There are 6 each side.
Now I'm feeling lazy
Plank next to keel. Inside looking down.
Another rotted plank on bottom.
Starboard side. Think at some stage it must have been sitting on its side outside.
The quarters and some hanging knees are rotted too though I can do those. It is mainly to scarf in about five plank repairs.. Need to put some floorboards in as well. Planks made of 1/4"marine ply. I have 6mm sheet.
A shipwright also advised me to add a heavier timber skeg keel to the existing. It is the same as this all along. Also suggested a bulkhead about 2ft back to strengthen the bow quarters.
Ideally it would be good to replace all planks. There are 6 each side.
Now I'm feeling lazy
Re: Vessel befitting a Seagull at last.
How sad I thought she would be an easy repair, honestly I don't think she's worth the effort Dry Rot
would be a lot worse than the photos show . It would be easier to do a new build I'm guessing the shipwright
saw it about 4 or 5 years ago.
John
would be a lot worse than the photos show . It would be easier to do a new build I'm guessing the shipwright
saw it about 4 or 5 years ago.
John
- Charles uk
- Posts: 4960
- Joined: Wed Feb 27, 2008 4:38 pm
- Location: Maidenhead Berks UK
Re: Vessel befitting a Seagull at last.
Hugz does anyone run a wooden boat building course near you? what's left of your boat would make an ideal project for a class of apprentices, it's a beautiful shape it would be a tragedy to let it crumble away, very close to criminal!
If it was in this country, I would be tempted to take a GRP mould from it, if it's still true.
If it was in this country, I would be tempted to take a GRP mould from it, if it's still true.
Make it idiot proof and someone will make a better idiot.
Re: Vessel befitting a Seagull at last.
Good to hear from Hugo again One of the stalwarts of the forum Yes a lovely boat, and well worth a decent restoration. I'm sure Charles suggestion has some merit, perhaps a great project for a boat/woodwork class. It would give you access to all the correct tools too.
Last edited by Oyster 49 on Sun Dec 02, 2018 7:25 pm, edited 1 time in total.
Re: Vessel befitting a Seagull at last.
Ok, you guys have inspired me I've been through contacting boat building schools and technical colleges but without a good result. Space always seems to be the deterrent. I did have a promising lead with a maritime inspired "Mens Shed" but alas the space was again a problem. So.... I'll do it myself. I have a parking space and have to work on it there and include the trailer too! Fortunately it is a dry day today (1st in many days) so cover off and let her dry and make a timber frame to bolt to trailer so can work on boat hull up. She hasn't got a name and I'm thinking of Charon (of Greek Mythology, is Stelios still here?) It is actually not in as bad shape as I imagined. I think a long shaft naval SD will compliment her well. I could probably join a wooden boat forum but I think there is enough experience on here to guide me . Timber is a new medium for me.
Re: Vessel befitting a Seagull at last.
Here is my first question. In my travels I've been told of a product that can be applied to spongy wood that then soaks in and sets rendering an easy repair. There are a couple of spongy bits that have not yet rotted out.
Look it has been repaired before:
Look it has been repaired before: