Search found 831 matches
- Tue Mar 19, 2019 11:32 pm
- Forum: General Topics
- Topic: Silver Century not starting
- Replies: 18
- Views: 27267
Re: Silver Century not starting
Do you have a spark? Sometimes the HT lead may look ok but a lot of the time that is the issue. If you don't get a cough with the engine start / wd40 / CRC or fuel in the plug hole then I put 10c on the HT lead.
- Tue Mar 19, 2019 11:25 pm
- Forum: General Topics
- Topic: Gear oil and two stroke
- Replies: 47
- Views: 67552
Re: Gear oil and two stroke
After you first outing, tip the oil out into a jar and let it sit for a few days... You will see a change as the water sinks to the bottom.
Judge for yourself if you think the oil is still good put it back and top it up.
Judge for yourself if you think the oil is still good put it back and top it up.
- Sat Mar 09, 2019 11:14 pm
- Forum: Help
- Topic: Thread size in the Villiers center tube
- Replies: 6
- Views: 14225
- Sat Mar 09, 2019 6:36 am
- Forum: Wanted
- Topic: Locking latch
- Replies: 32
- Views: 57493
Re: Locking latch
but might be 3D printable It might be but who will draw it up? and if they did would there be a demand for them. If there was a demand I would give it a go.... It would be a good part to print in PETG It would have cost quite a bit to have the tooling made to do that, but the parts may have been ch...
- Sat Mar 09, 2019 6:27 am
- Forum: Help
- Topic: Thread size in the Villiers center tube
- Replies: 6
- Views: 14225
Re: Thread size in the Villiers center tube
Ok, so I have no idea what thread it is... and I had a look in my "guide to world screw threads book"! Major dia. is 8.8mm IMG_4263.JPG Thread pitch is 32 tpi 60° (the other end is 28 TPI 60°9.6mm) IMG_4264.JPG What I need is All of these sizes. I know the thread size so that is not an iss...
- Fri Mar 08, 2019 8:49 am
- Forum: Help
- Topic: Thread size in the Villiers center tube
- Replies: 6
- Views: 14225
Re: Thread size in the Villiers center tube
I will find out the thread if you can measure up the plastic air intake for me.
I know the thread for the intake I just need to know the rest of the sizes so I can draw one up.
I will get the thread for you in the morning
I know the thread for the intake I just need to know the rest of the sizes so I can draw one up.
I will get the thread for you in the morning
- Sun Mar 03, 2019 9:46 am
- Forum: General Topics
- Topic: villiers lever screws
- Replies: 7
- Views: 10976
Re: villiers lever screws
Once it has been worked out let me know so it can be added to this thread:
viewtopic.php?f=2&t=6040
viewtopic.php?f=2&t=6040
- Mon Feb 25, 2019 10:19 am
- Forum: Wanted
- Topic: Locking latch
- Replies: 32
- Views: 57493
Re: Locking latch
Are you saying you are going to get it and do the job? Thanks for offering!
- Mon Feb 25, 2019 10:16 am
- Forum: General Topics
- Topic: Stop end in a pistons gudgeon pin
- Replies: 10
- Views: 12922
Re: Stop end in a pistons gudgeon pin
Just leave it be as it is. The motor will still work!
- Mon Feb 18, 2019 4:08 am
- Forum: General Topics
- Topic: How does a recoil starter work ?
- Replies: 9
- Views: 12549
Re: How does a recoil starter work ?
Depends on the recoil starter you have!
Try it and see!
I do not have one so I don't really know.... when you find out show us.
Try it and see!
I do not have one so I don't really know.... when you find out show us.
- Sat Feb 16, 2019 7:33 am
- Forum: Boats Suitable For Seagulls
- Topic: Fixing the 20 footer
- Replies: 34
- Views: 68881
Re: Fixing the 20 footer
IMG_4097.JPG IMG_4098.JPG IMG_4099.JPG IMG_4096.JPG IMG_4102.JPG The lifter is made from 65mm x50mm 6mm wall Ali with a 24v hospital bed lifter actuator that I got from a scrap yard. You could also use a powered car seat motor or window motor. I run mine on a small 12v lead acid battery as it was t...
- Sat Feb 16, 2019 7:13 am
- Forum: Help
- Topic: Drive Shaft assembly query
- Replies: 5
- Views: 10269
Re: Drive Shaft assembly query
All good!
The offer is out there if you need it!
The offer is out there if you need it!
- Sat Feb 16, 2019 7:10 am
- Forum: Help
- Topic: Flywheel colour match
- Replies: 8
- Views: 13168
Re: Flywheel colour match
As far as I know they can scan (not 100% sure) if not Bunnings can scan then go to Wairau Paint
- Thu Feb 14, 2019 10:07 am
- Forum: Help
- Topic: Drive Shaft assembly query
- Replies: 5
- Views: 10269
Re: Drive Shaft assembly query
If you need to have a look at one that is not in bits give me a shout. (or the book)
You going down the Waikato this Easter?
You going down the Waikato this Easter?
- Thu Feb 14, 2019 10:05 am
- Forum: Help
- Topic: Flywheel colour match
- Replies: 8
- Views: 13168
Re: Flywheel colour match
Just go to carcolors or wairau paint centre and they will mix the colour you need.Appreciate the info. I will give it a go.
Luckily enough, I can get the colours over here.
Thanks again. (Kia ora rawa atu)
Greyman56
Both on the North Shore, Auckland...... Like Me!
Welcome