Search found 627 matches: Flywheel removal

Searched query: flywheel removal

ignored: flywheel

by Raya
Wed Mar 04, 2020 8:21 am
Forum: General Topics
Topic: electrolysis rust removal
Replies: 2
Views: 602

Re: electrolysis rust removal

Alas no, this cylinder is off AD4233, a 1948 outboard. It has the slotted welsh plugs instead of the hex plugs that the D would have. I could use it on the D but will keep it together with it's crankcase for originality. I have the matching gearbox and prop so will assemble this one after the D. I'm...
by Charles uk
Wed Mar 04, 2020 6:28 am
Forum: General Topics
Topic: electrolysis rust removal
Replies: 2
Views: 602

Re: electrolysis rust removal

This could be the cylinder that belonged to your D.
by Raya
Wed Mar 04, 2020 4:12 am
Forum: General Topics
Topic: electrolysis rust removal
Replies: 2
Views: 602

electrolysis rust removal

Included in a box of bits I came across, were most of the parts from an early 1948 AD. The cylinder was in poor condition being completely blocked with rust and there was a crack around one of the securing bolts that probably occured during the dismantling. The rust was rock hard and wouldn't easily...
by never-outbored
Sun Jan 26, 2020 11:06 pm
Forum: General Topics
Topic: Century 100 restoration.
Replies: 15
Views: 2250

Century 100 restoration.

... as i’m led to believe the villiers coils are temperamental. The one man flywheel removal was no mean feet in itself, but with a bit of creative thinking i found a solution: ...
by Chris B
Fri Sep 20, 2019 2:57 am
Forum: General Topics
Topic: Cleaning steel tanks
Replies: 9
Views: 2929

Re: Cleaning steel tanks

... Just make sure it's bare metal and not plated. If you're going to treat the inside of a Seagull fuel tank then your preparations need to include removal of the Ewarts fuel tap and closing the vacant fuel port with a blanking plug. Probably obvious but nonetheless worth mentioning that if you're ...
by Chris B
Thu Sep 19, 2019 4:16 pm
Forum: General Topics
Topic: Cleaning steel tanks
Replies: 9
Views: 2929

Re: Cleaning steel tanks

... long range Seagull tanks. And having tried various methods of corrosion removal, the technique I eventually came to favour for small steel tanks ... so can driving to the supermarket, or getting tangled up in a Seagull flywheel. Chris
by Hugz
Tue Sep 17, 2019 4:30 am
Forum: General Topics
Topic: Cleaning steel tanks
Replies: 9
Views: 2929

Cleaning steel tanks

... of salt is also dead cheap, can be obtained similarly. Phosphoric acid: at least 40% strength is required. Plenty on eBay too. Stage 1: Gunge Removal To start, pour out all the remaining petrol from the tank into a can and if it's still any good save it for use at another time or in your lawnmower. ...
by Gannet
Fri Jul 19, 2019 8:41 am
Forum: General Topics
Topic: FV3048 - Overboard!
Replies: 8
Views: 2733

FV3048 - Overboard!

... poured out of the carb, and I wondered what damage had been done, especially as it was running when it took the dive overboard. Anyway, after plug removal and flushing the magneto with fresh water, squirting lots of WD40 into the engine and the points box, I put it into the boot of the car to examine ...
by Journeyman
Mon Jul 08, 2019 9:33 am
Forum: The Discussion
Topic: Flywheel removal revisited
Replies: 1
Views: 3174

Re: Flywheel removal revisited

Have not needed to use heat on any of mine, here is my setup, this was removing the flywheel on the Century Plus. Outboard 078.jpg First a ball bearing to transfer the blow to the shaft. Then hang the engine from a beam clear of everything. Outboard 075.jpg As you ...
by 0tis
Sun Jul 07, 2019 1:09 pm
Forum: The Discussion
Topic: Flywheel removal revisited
Replies: 1
Views: 3174

Flywheel removal revisited

... with no success. Penetrating fluid applied for days. Really don't want to hit it any harder for fear of damage. Any thoughts on heating the flywheel to loosen it? Thanks for any thoughts It's a 74 Forty Plus.
by tambikeboy
Thu Jul 04, 2019 5:44 pm
Forum: Help
Topic: Drive spring carrier removal
Replies: 1
Views: 1503

Re: Drive spring carrier removal

Different from the efnr it has a roll pin going through the spring carrier a good set of mole grips on the inside shaft and try rotating with a long screwdriver wedged between the two lugs of the carrier (with heat) and don't let the molies slip
by andrew
Sun Jun 02, 2019 1:25 pm
Forum: Help
Topic: Drive spring carrier removal
Replies: 1
Views: 1503

Drive spring carrier removal

Looking for a bit of advice on removing the drive spring carrier on a 170 (I believe same gearbox as EFNR). I’ve tried gentle prying/tapping but I don’t want to bend/damage the prop shaft, as I’m only able to pry from one side at a time. Gave it decent amount of heat. Pulling it off with brute force...
by Charles uk
Tue Apr 30, 2019 4:32 pm
Forum: Help
Topic: EFNR564FF9 Gearbox Pinion Gear Removal
Replies: 9
Views: 3971

Re: EFNR564FF9 Gearbox Pinion Gear Removal

What did you decide to do in the end Dave?
by Charles uk
Sat Apr 27, 2019 3:40 pm
Forum: Help
Topic: EFNR564FF9 Gearbox Pinion Gear Removal
Replies: 9
Views: 3971

Re: EFNR564FF9 Gearbox Pinion Gear Removal

Why didn't you follow Naughty Bits methods of pinion assembly removal? with the sacrificial brass drift. It looks from your pictures that you've destroyed the hardness of the bevel pinion gear, so you'll need a new one. The bevel pinion sleeve with bushes ...
by daydreamingdave
Wed Apr 24, 2019 11:19 pm
Forum: Help
Topic: EFNR564FF9 Gearbox Pinion Gear Removal
Replies: 9
Views: 3971

Re: EFNR564FF9 Gearbox Pinion Gear Removal

Having removed the unit I feel I should strip it into its constituent parts.
However, I fear this may destroy it and, well, what’s the point.
I also feel it has probably been damaged in the process, so what is to lose?
Has anyone done this before? Any tips?